Device Specifications
• neoVI 3G Architecture over 10x performance over previous
devices
• 3 DSPs and 1 RISC processor for 125 MIPS of processing
• Power Consumption (typical) : 150mA @ 14.4 VDC
• Sleep Power Consumption (typical) : 12mA @ 12.0 VDC
• Power Supply: 5.5-27 Volt Power Operation
• Temperature Range: -40C to +85C
• Vehicle Connectors : 25 Pin male D-SUB and 9 Pin Male
D-SUB
• Warranty: One Year Limited Warranty
• Firmware: Field upgradeable design (flash firmware)
• General Purpose IO: 6 MISC IO (0 - 3.3V), 4 IO can be
configured as analog
• General Purpose IO rate report interval: 10 Hz to 1 Khz or
based on digital change
• Microsoft Certified USB drivers
• Isolated USB
• Stand-Alone Mode Including Scripting, Receive Messages,
Transmit Messages, Expressions, IO, and Transport Layers
• ICS TimeSync for Multiple Hardware Synchronization
supports all neoVI 3G devices
• J2534 and RP1210 A/B compatible for CAN/ISO15765,
Keyword, ISO9141, and J1850 VPW
• microSD card slot support for up to 16 Gigabytes of storage
(or up to the limit of newer SDHC cards). The removable card
is formated using FAT32 for direct usage in a PC.
• Battery backed real time clock (RTC)
Networks - General
• 64 Bit time stamping to accuracy of 10 microseconds on CAN
and LIN networks and never overflows. 0.5 microsecond
accuracy timestamp available if using one network only
• Simultaneous operations on all CAN/LIN/J1850 networks
• Transmit message double-buffering on all networks allows
back to back message transmission |
Network Specifications
6x CAN Channels
• 4 Dedicated ISO11898 Dual Wire CAN Physical Layer (TJA1040)
• 1 Dedicated ISO11519 Low Speed Fault Tolerant CAN Physical Layer (TJA1054A)
• 1 Dedicated Single Wire CAN Physical Layer GMW3089 / SAE J2411 (MC33897)
• CAN 2.0B Active
• Up to 1 M-Bit Software Selectable Baud Rate (auto baud capable)
• Capable of generating and detecting error frames
• Logic Analysis of CAN Waveform with 25 nanosecond resolution
• Graphical Bit Time / Baud Rate Calculator
• Listen only mode support
• Unterminated network detection
• High Speed Mode, Test Tool Resistor, and High Voltage Wakeup support
4x LIN (Local Interconnect), ISO9141, Keyword 2000, or K and L Line
• Full support for LIN 1.X, 2.X and J2602
• LIN J2602 / 2.X compatible physical layer
• Software Selectable LIN Master Resistor
• Capable of Generating LIN Waveforms (Including Errors) Using Dedicated Output Compare Hardware
• UART Based State Machine
• Initialization Waveforms including Fast Init, Five Baud, and Custom
• Programmable Timing Parameters including Inter-Byte, TX Inter-Frame, RX Inter-Frame and Initialization Waveforms (0.5 ms Resolution)
• Software Selectable Baud Rate
• LIN Bus Monitor Mode identifies errors: Sync Break Error State and Length, Sync Wave Error, Message ID parity, TFrameMax/Slave Not Responding, Checksum Error andTransmit Bit Errors.
• LIN Bus Master Mode operates at same time as LIN Bus Monitor
• LIN Bus Slave simulation - with or without an LDF file
• LIN Bus hardware schedule table with support for LIN diagnostics
1x J1850 VPW (GM Class 2)
• VPW Physical Layer capable of TX and RX operations (MC33390)
• Reception of IFR data during TX and RX|
1x GM CGI
• Software Enabled (disables LIN2)
• Programmable Bit Rate
• Full block mode message reception only
• Transmission Option available in CGI Simulation Toolkit
|
